ORIGINAL JAF 7PIN BB5 CABLE SET IPMART BRAND IN STOCK

Original JAF BB5 Cables Set iPmart 1.Easy flash 2 2.Nokia 1100 3.Nokia 1202 4.Nokia 1680C 5.Nokia 2330C 6.Nokia 2630 7.Nokia 3120C 8.Nokia 3600S 9.Nokia 5130XM 10.Nokia 5300 11.Nokia 5310XM 12.Nokia 5320XM 13.Nokia 5610XM 14.Nokia 5630 15.Nokia 5800XM 16.Nokia 6085 17.Nokia 6100 18.Nokia 6131 19.Nokia 6208C 20.Nokia 6220C 21.Nokia 6233 22.Nokia 6260S 23.Nokia 6270c 24.Nokia 6300 25.Nokia 6303 26.Nokia 6500C 27.Nokia 6600S 28.Nokia 6680 29.Nokia 6700C 30.Nokia 6710s 31.Nokia 6720c 32.Nokia 6730c 33.Nokia 6750 34.Nokia 6790 35.Nokia 7100S 36.Nokia 7500 37.Nokia 7510S 38.Nokia E50 39.Nokia E51 40.Nokia E52 41.Nokia E65 42.Nokia E66 43.Nokia E71 44.Nokia E72 45.Nokia E75 46.Nokia E90 47.Nokia N70 48.Nokia N73 49.Nokia N75 50.Nokia N76 51.Nokia N79 52.Nokia N80 53.Nokia N82 54.Nokia N85 55.Nokia N90 56.Nokia N91 57.Nokia N95 58.Nokia N95 8GB 59.Nokia N96 60.Nokia N97

HUAWEI C2607 UNLOCKING SOLUTION

HUAWEI C2607 UNLOCKING SOLUTION HERE. After a long time, this file comes for unlock the cdma huawei c2607 handset with a simple and small flashing of around 8 minutes. For this one pst tool is required and 2607 unlock xml file i.e. file name (C2607-India(TATA)- C02B105 UNLOCKED), with which some of the versions can easily be unlocked, and if the version is some higher than it, then it will unlock in advance combo box. Well first of all install the pst tool , then open the tool, where you have to browse the unlock file , and then off the parameter option, and select the accurate comport, whatever interface u r using, then press the start download button. after download finish complete, it will say the message , that please connect another handset, then we have to plugout the cable, and handset would unlock and can use any cdma ruim in it.

here is the file and tool for it.

http://www.ziddu.com/download/7906418/PSTupdatedversion122.rar.html

http://www.ziddu.com/download/7906386/C2607-IndiaTATA-C02B105UNLOCKED.rar.html

NOKIA 1200, 1208, 1650 INSERT SIM NEW SOLUTION

NOKIA 1200, 1208, 1650 INSERT SIM NEW SOLUTION HERE FOR THE FIRST

This insert sim fault is very common which comes in nokia handsets of dct4 models mostly, it can be of many reasons, like sim ic damaged or supply not comes from power ic , uem or even of battery connector middle pin if not connecting with the battery properly.

But now the solution is in some other way and its a good shortcut that is invented. One very good shortcut is just remove the small capacitor which is placed on the left upper corner of the UEM power ic that is shown right in the picture here and after that you have also to short one pin of the sim tray i.e. on pin on the left lower side. By doing this, insert sim fault will get ok, its 100% tested solution. For more info, contact at yahoo id on this site given.

RSD LITE LATEST SOFTWARE 5.1.8 VERSION

Here is now the latest tool of rsd lite 5.1.8 version for attaching , flashing, window based handsets of MOTOROLA BRANDS like moto Q , data to q , etc. which does not make any comport in device manager, but only this latest rsd lite version can detect this handsets by usb and easily connected, by this we can flash the handset, all nam programmings can manage in it, by which we can write any prl file also to it. Actualy, old versions of rsd lite software does not attach these latest handsets and also there is no nam programming option is available in them. In this we can flash .shx files into it http://rapidshare.com/files/140809111/RSD_CMDA_General_5.1.8_Installation.zip.html

NES GAMES FOR MP4 -MP5 PLAYERS

MP4 & MP5 PLAYERS MARKET NOW GOING STRONG DAY BY DAY, as there are coming alot of functionalities and internal memory + external mmc card facilities, even nowadays, MP6 PLAYERS ARE ALSO LAUNCHING IN THE FOREIGN MARKET. Well alot of people make their entertainment source and in the free time they get satisfied by playing games and shuffling audio, video songs, using fm radio and even by video recording. Actualy the numbers attached with the words MP- like mp3 denotes that it has three type of functions, mp4 denotes , it has 4 types of functions such as , audio songs, video songs, images and games, and mp5 denotes 5 functions that is 5th function is of camera. These has internal memory starts from 1gb to 8 gb normally. Well here are some good working tested games for mp4, mp5 players, because normaly nes games are compatible in them. so here is the link for that and you have only to copy paste games into the right folder of the player i.e. named of games. http://www.ziddu.com/download/7660543/nesgamesmp5.rar.html

Hi dear users, there is one more information and software to all of you, which is absolutely free i.e. to write new imei no. for mtk cpu chinese handsets, but it has limit of demo version to use only 20 credits free for your handsets with username and password , but legally its not genuine so much, because in this online tool, nobody have to deposit any proofs or not to give any reciept to customer, but handset will get ok, so its not approved by the COAI , but its working to write imeis online.

So here is the tool and username , password which one can use with their any interface or pinfinder that connects rx, tx, gnd, vbat automatically like spider -man box, ve-pro , cpf box, infinity pin finder, etc.

well you can try with this, and post comments what u get results properly.

User : giw

Pass: 1234 http://www.hardnsoft.biz/giw/setup.exe 20 credits free

IMEI LEGAL OR ILLEGAL NEWS

Hi dear visitors, it must be cleared to you, that only IMEI changing is only legal through MSAI because as it is registered with COAI (CELLULAR OPERATORS ASSOCIATION OF INDIA) AND DOT(DEPARTMENT OF TELECOMMUNICATIONS).

MSAI is exclusively authorized body in India by GSM Association (GSMA) to perform Genuine IMEI Implant program (GII).MSAI is working in partnership with Cellular Operators Association of India (COAI) and Department of Telecommunications (DOT) to implant the genuine IMEI numbers on to the mobile handsets which are carrying bad/non genuine IMEI numbers as a one time Amnesty Program. The Service partners have to follow the process and guideline for this program as prescribed by Department of Telecommunications as advised by the security agencies.

For that to start with msai, some tools are required as mentioned below:

Computer with latest configuration Printer Scanner Web Cam Any Pinfinder Box for Chineese Forum Broadband Internet

TO USE , WE ALSO NEED SPIDERMAN BOX OR ANY OTHER INTERFACE I.E. PINFINDER BOX , THE HANDSETS WHICH CAN'T BE DETECT BY THE BOX, THAT WE CAN FIND THIER RX, TX , GND AND VBAT POINTS AND ATTACH THE HANDSET AND THEN LOGIN WITH USERNAME , PASSWORD , THEN PRESS READ INFO AND THEN PRESS WRITE IMEI (software automatically select existing IMEI and write it on the phone from database.)

OPEN THIS SITE FOR YOUR SATISFACTION- http://www.asianelectronics.org/ and http://www.msai.in/

V3 MOBILES - DISTRIBUTORSHIP AND SERVICE CENTERS

LATEST V3 MOBILES - CDMA AND GSM GOOD RANGE WITH MULTIMEDIA FUNCTIONS AT BEST PRICE

V3 MOBILES (PRABHAT GROUP INDIA PVT. LTD.) PROVISION OFAUTHORIZED SERVICE CENTER AND DISTRIBUTORSHIP

HI DEAR ALL USERS, HERE IF ANYBODY REQUIRED V3 MOBILES (PRABHAT GROUP INDIA PVT. LTD.) AUTHORIZED SERVICE CENTER AND DISTRIBUTORSHIP  IN THEIR RESPECTIVE CITIES  IN NORTH REGION - PUNJAB, HIMACHAL, HARYANA AND J&K,  PZ CONTACT AT yahoo id - pawanlovesu2004@yahoo.com (NORTH REGION)

AND FOR IF ANY OTHER REGION, THEN ALSO CONTACT HERE

HTC UNIVERSAL MODEM DRIVERS

Hi users , here is the htc modem drivers of any brand, which is needed to access internet or to make connectivity of the handset with the computer, and its port no. will be in its inner functions. By which we can convert any HTC cdma handset into any cdma network working like reliance, tata, virgin or ping. These are very useful drivers and after installation , when we plug in its usb cable it will automatically took its suitable drivers. Here is the driver link http://www.ziddu.com/download/7442051/wmodemdrivershtc.rar.html

ABOUT CLASSIC 7- SERIES UNLOCK SOLUTION

HI BROTHER, HERE IS NOW LATEST SOLUTION FOR CLASSIC - 7 SERIES AVAILABLE BUT ITS PASSWORD IS YET REMAINING, IF YOU SPREAD THIS FORUM MORE AND KEEP ON GOOD POSTING, THEN SOON PASSWORD WILL BE ALSO HERE .( MODELS - 702, 703, 731, 732 ) - UNLOCKING, SOLUTION , DOWNLOAD FROM - PASSWORD GIVEN http://mobilesoftwareworld.forumotion.com/classic-models-f46/classic-7-series-unlocking-available-t2.htm

MX-KEY SUPPORT UNLOCKING MODELS LIST

Supported BB5 No TP Unlock: RAP3GV2: -6630 (RM-1)* -6680 (RM-36)* -6681 (RM-57)* -6682 (RM-58) -N70 (RM-84)* -N70-5 (RM-99) -N71 (RM-67) -N90 (RM-42)* -N91-1 (RM-43) -N91-8GB (RM-43)* -N91-5 (RM-158)* -N93 (RM-55) RAP3GV3:;Relock also supported -3109c (RM-274) -3110c (RM-237) -3250 (RM-38) -3500c (RM-272) -3500cb (RM-273) -5200 (RM-174) -5200b (RM-181) -5300 (RM-146)* -5300b (RM-147) -5500 (RM-86) -5700 (RM-230) -5700 (RM-302) -6085 (RM-198) -6086 (RM-188) -6086b (RM-260) -6125 (RM-178) -6126/6133 (RM-126) -6131 (RM-115) -6131 NFC (RM-216) -6136 (RM-199) -6151 (RM-200) -6233 (RM-145)* -6234 (RM-123)* -6280/6288 (RM-78)* -6290 (RM-176) -6300 (RM-217)* -6300b (RM-222) -7370 (RM-70) -7373 (RM-209) -7390 (RM-140) -8600 (RM-164) -E50 (RM-170) -E50 (RM-171) -E50 (RM-172) -E61 (RM-89) -E61i (RM-227) -E62 (RM-88) -E65 (RM-208) -N73-1 (RM-133)* -N73-5 (RM-132) -N75 (RM-128) -N76 (RM-135) -N76 (RM-149) -N77 (RM-194) -N80-1 (RM-92) -N80-3 (RM-91) -N92 (RM-100)SL2: -3120C (RM-364)* -3555 (RM-277) -3555b (RM-257) -5310 (RM-303)* -5310b (RM-304) -5610 (RM-279) -5610d-1(RM-242) -6263 (RM-207) -6300i (RM-337) -6301 (RM-322) -6500s (RM-240)* -6500c (RM-265)* -6555 (RM-289) -7500 (RM-249) -7900 (RM-264) -8800 (RM-165) exception(Not supported, new security): -3600s(RM-352) V56.26 -5310 (RM-303) V58.58 -6500c (RM-265) V59.45 -6500s (RM-240) V59.60 -6300 (RM-217) V57.20 RAPIDO: -N95 (RM-159)* -N95 (RM-245) -N95 (RM-160) -E90 (RA-6) SL2: -6110 (RM-122) -6120c (RM-243)* -6121c (RM-308) -6124c (RM-422) -6210 (RM-367) -6220c (RM-328) -6290 (RM-176) -6650 (RM-400) -E51 (RM-244)* -E66 (RM-343) -E71 (RM-346) -N79 (RM-349) -N95-2 8GB (RM-320) SL2 with Protected PM: -E75 (RM-412)* -N96 (RM-247) -5800 (RM-356)* -------------------------Supported DCT4PLUS Patch Unlock: -1110i (RH-93)* -1112 (RH-93)* -2310 (RM-189)* -2610 (RM-189)* -1650 (RH-86)* -1200 (RH-99)* -1208 (RM-205) -1209 (RM-105)* -2680 (RH-392) -5000d (RM-362)* -2600c (RM-340)* -2626 (RM-291)* -2630 (RM-298)* -2670 (RM-258)* -1680c (RM-394)* -2330c (RM-512)* -2323c (RM-543)* -2720a (RM-519)* -7100s (RM-438)* *) tested.

http://www.ziddu.com/download/7204023/supported_modelsmxkeyunlocking.txt.html

BLACKBERRY 7XXX, 8XXX, 9XXX UNLOCKING BY MFI FILES

Blackberry to open set lock by code remote unlocking FIRST OPEN SIM SETTINGSTHEN PRESS " MPED "THEN SELECT SIM OPTION THEN PRESSED LEFT BOTTOM BUTTON WITH " MPE2 " THEN ENTER UNLOCK CODE IN IT, PHONE IS UNLOCKED But to take its code by imei no. , we have to get it with any registered server online alot of there. This process is now old for old handsets, and is running for new and latest handsets which cannot be unlock by flashing or furious gold box.

Well alot of blackbery models like 7XXX, 8XXX AND 9XXX are also unlocking by flashing with mfi files. This process is also easy if done by the proper way and guidance. I HAVE ALSO UNLOCKED BLACKBERY MODEL 7100R, 8110, ETC. BY MFI FLASHING. The process starts like this, first of all we need the particular model's firmware file which we have to unlock country lock, then we need complete setup of 718 mb in zip form, in which there is MML SETUP, which we have to install and it will make directory c:\mml\. Then we have also .netframework install on our system. Then we need one configuration file named "configuration.xml " which we have to replace it with the file made in c:\mml\configuration, this is done if you want to unlock handset without using internet.After that we need blackberry usb and modem drivers latest version i.e. 4.7. After installing all setups, then the data of 718 mb all mfi zip folders we have to extract it in one folder and have to be replaced it all folders like bin, config etc to the folder made in c;\mml\, because if we do not paste it all there, software will give an error after erasing that load mfi file not find on local hard drive. So remember it to do that in the same way as mentioned, Also install MFI LOADER SETUP, Through which we have to tick mark on erase and auto start options. and when all drivers will be install on it. it will automatically erase mfi and load its unlocked mfi file, After that on Handset NO. 1 WILL BE SHOWN AFTER PASSING FLASH. THEN WE HAVE TO TYPE THE WORD " S T A R T " TO COME OUT FROM DM MODE. THEN THERE WILL DISPLAY "NO APPLICATION DATA" ERROR, NOW HERE WE NEED HANDSET FIRMWARE APPLICATION FILE AND BLACKBERRY DESKTOP SOFTWARE , TO INSTALL ALL ITS ORIGINAL APPLICATIONS, AND THEN AT LAST AFTER ALL DONE ON HANDSET NETWORK WILL SHOW OFF, THEN GO IN NETWORK SETTINGS AND SELECT PROPER OPTIONS, AND NOW YOUR HANDSET IS READY TO USE ANY GSM RUIM IN IT. ONE MORE PRECAUTION WE HAVE TO TAKE IS TO DELTE VENDOR.XML FILE i.e. in c:\program files\common files\research in motion\apploader, after mfi flashing and before installing its firmware file. FOR MORE DETAILS CONTACT ON ID. HERE IS SOME DATA BELOW - http://www.ziddu.com/download/7104977/blackberryhardwareandsoftwarelinks.txt.html

http://www.ziddu.com/download/7105049/FrequentlyAskedQuestionsAboutBlackBerryphones.doc.html http://www.ziddu.com/download/7105056/Configuration.rar.html http://www.ziddu.com/download/7104952/blackberylatest4.7fulldesktopsoftwremanager.txt.html

USB DATACARDS MODEM INTERNET ACCESSING PROCEDURE

There are several range of usb wireless modems through which we can access internet with good speed and its portable, we can take it anywhere and can use anytime if u have unlimited plan in it. Data cards running in the market are reliance mg880, huawei ec220, ec321, ec325, tata 1080, tata photon etc. Well every data card has its own features and softwares to access internet. Well for using huawei ec325 modem, if u want to reliance ruim in it, then its not need to unlock the device, but if u want to use tata ruim in it, then we have to unlock it by first updating its firmware, after that we need its software setup, install it properly and then plug in the device, it will automatically install all modem drivers into the pc, then just open the network connection setting in setting option, click new button and type any profile name and number to dial is #777, username is "internet" and password is also "internet" and then save it and click the connect button, internet will authenticate and will be connected successfully. Well for using net in 1080 data card tata, if we want to use reliance ruim in it, then it needs also to be unlocked with its download tool software and unlock file that i have mention in my site before , search it. Then install tata modem software and you can access good internet in it. But the best speed and efficiency is going nowadays is of Tata photon that is the latest launched. But where network is week of tata, there got some problems. These modems are best to use on the laptops, notebooks and palmtops because its portable, wireless and easy to use. We can also make calls anywhere by using earphones, either we have prepaid internet connection or post paid connection. Well for more information, comments pz. HERE EC325 DRIVERS http://www.ziddu.com/download/6932262/EC325_DRIVERS.rar.html

NOKIA MOBILE MB LATEST VERSION 5.2 FULL

Nokia Mobile mb from starting is a very usefull and successful software by which we can download alot of data like images, movies, ringtones and games to the handset. But before doing all this process, we have to attach the particular handset with the help of its particular usb or serial datacable, because this software has both serial and usb functionality. Secondly, we need handset drivers or modem drivers through which its usb port is made and handset will show and attached in the mobile mb software.

In this software, we can download data in Nokia, sony ericson and Motorola handsets in a wide range, their model details given below which can be done. After installaion this software in the computer, we have to crack it for accessing it full version by click on registry entry file. When we will open the tool, then press start mobile mb button, after that open file option and then click settings button, then in that there will be two more options, one is connections and second is advanced, in connections, click add connection, in that more three options are there to attach the handset i.e usb or serial cable, bluetooth and infrared connections. In usb or serial cable option, nokia, sony ericson and other options, by selecting proper cable brand like dku-2, dku-5, or fbus we can attach handsets and in second option i.e. ADVANCED, we can make settings of 3gp videos and ringtones etc. After that we can easily transfer the compatible data to the handsets.

These types of models can be loaded :

Nokia 1112B Nokia 1600/1600B Nokia 2112/2115i/2118 Nokia 2125/2125i Nokia 2255 Nokia 2300/2300B/2310 Nokia 2355*/2362*/2365i*/2366i* Nokia 2367i* Nokia 2600/2600B Nokia 2610/2610b/2611/2626 Nokia 2630/2650/2651/2652 Nokia 2660 Nokia 2760 Nokia 2855*/2855i*/2865*/2865i* Nokia 2875*/2875i* Nokia 3100/3100b/3105/3108 Nokia 3109 Classic/3110 Classic/3120/3120b Nokia 3125/3128/3129/3152 Nokia 3155/3155i Nokia 3200/3200B/3205/3205i Nokia 3220/3220b Nokia 3230*/3250* Nokia 3300/3300B Nokia 3500 Classic Nokia 3510 Nokia 3510i/3520/3530/3560 Nokia 3570/3585/3585i Nokia 3586/3586i/3587i Nokia 3588i/3589i Nokia 3590 Nokia 3595 Nokia 5100/5100A/5140/5140b Nokia 5140i Nokia 5200* Nokia 5300* Nokia 5310 XpressMusic Nokia 5500* Nokia 5610 XpressMusic Nokia 6010/6011i/6012/6015 Nokia 6015i/6016i/6019i/6020 Nokia 6020B/6021/6030/6030B Nokia 6060/6060v/6061/6066 Nokia 6070/6070B/6080/6085 Nokia 6085H/6086/6086b Nokia 6100/6101/6101b/6102 Nokia 6102b/6102h/6102i/6103 Nokia 6103b/6108/6111/6112 Nokia 6125/6126/6126h/6131 Nokia 6133/6133b/6135/6136 Nokia 6136b/6151/6152/6155 Nokia 6155i/6165/6165i/6170 Nokia 6170B/6175i/6178i Nokia 6200/6220/6225/6225i Nokia 6230/6230b/6230i/6233 Nokia 6234/6235/6235i/6236i Nokia 6255/6255i/6256/6256i Nokia 6260*/6260b* Nokia 6265/6267/6265i/6270 Nokia 6275/6275i/6280/6282 Nokia 6288 Nokia 6300/6300B/6301 Nokia 6305i Nokia 6310i Nokia 6500 classic/6500 slide/6555/6555b Nokia 6555c/6560/6585/6585i Nokia 6610/6610i Nokia 6620*/6630* Nokia 6650/6651 Nokia 6670*/6670b*/6680*/6681* Nokia 6682* Nokia 6800/6800A/6810/6820 Nokia 6820B/6820i/6822/6822b Nokia 7200/7200B/7210/7250 Nokia 7250i/7260/7270/7270B Nokia 7280/7280B Nokia 7360/7370/7373/7380 Nokia 7390 Nokia 7600 Nokia 7610*/7610B* Nokia 7710* Nokia 8600 luna Nokia 8800/8800d (Sirocco)/8801 Nokia 8910i Nokia 9300*/9300i* Nokia 9500*/9500b* Nokia E50* Nokia E60*/E61*/E62*/E65* Nokia E70* Nokia N70*/N70-5*/N71*/N71-5* Nokia N72-5*/N73-5*/N73*/N75-3* Nokia N80-3*/N80*/N80 (02)* Nokia N90*/N91-2*/N91-5/N91-6*/N92* Nokia N93*/N93-5*/N95*

Sony Ericsson D750i* Sony Ericsson F500* Sony Ericsson J300a*/J300c*/J300i* Sony Ericsson K300a*/K300c*/K300i* Sony Ericsson K500c*/K500i*/K506c*/K508c* Sony Ericsson K508i* Sony Ericsson K600*/K608i* Sony Ericsson K700c*/K700i*/K750c*/K750i* Sony Ericsson S700*/S710a* Sony Ericsson T610*/T616*/T618*/T628* Sony Ericsson T630*/T637* Sony Ericsson V600i* Sony Ericsson V800* Sony Ericsson W600* Sony Ericsson W800c*/W800i* Sony Ericsson Z500*/Z520a*/Z520c*/Z520i* Sony Ericsson Z600*/Z608* Sony Ericsson Z800* Sony Ericsson Z1010*

Motorola A835* Motorola C350g*/C353*/C359* Motorola C650* Motorola E1 ROKR* Motorola E398* Motorola E550* Motorola E680*/E680i* Motorola E815* Motorola v80* Motorola v180*/v186* Motorola v220* Motorola V3 RAZR* Motorola v300* Motorola v500*/v501*/v505* Motorola v535*/v545*/v550* Motorola v600* Motorola v620* Motorola v635* Motorola v710

http://www.ziddu.com/download/6914673/MOBIMBFULLLATEST.rar.html

HAIER D1200 UNLOCKING FOR ALL RUIM TESTED

Haier D1200 handset is a very smooth and good looking colored handset with good features in it. For a long time, its unlocking solution was in wait, but not wait is over, here i have its tested unlocking cp and boot rom files. Actualy there are two ways to unlock it. One way is to write its unlock srp file but by that only old tata sim will work, means phone locked contact service message will remove. To do that we need haier d1200 vpst tool and then its unlock srp file and its proper serial cable or rj-45 cable, first read it by zippo tool and then open its vpst tool and select srp file in script file option in settings, and select its exact port no. and just click update button, it will write its unlocking srp file and hanset will be unlocked for old tata ruim only. But for complete unlocking, two files have to be flashed by selecting unlocking cp and boot rom files in flash option, and then just press update, then message will appear on the tool "please reset handset manually", then just unplug cable and battery, and again plugin them. fill will automaticaly write and then same again repeat procedure as it displays above message, then second file will also write and hanset will restart and will be ready to access any cdma ruim in it without any problem. Here is the tool and unlock srp file , but for flash files contact pz, or wait later it will be posted free. http://www.ziddu.com/download/6886140/unlockd1200srptested.rar.html

HAIER C1000 UNLOCKING SOLUTION TESTED 100%

A good news to all of you on this happy diwali. Haier c1000 tata handset which was not unlocking before a long time, now it can be unlocked to any cdma ruim accessing network. This is grey body color handset with blue screen and black fonts. It has good battery backup and with solid body. This handset generally gets locked when we put another ruim instead of tata into it, even new tata ruim also not work in it and after putting any other ruim, its old tata ruim also stops working and a message display on the screen permanently without ruim also i.e. phone locked please contact service center". But now not to worry at all, here is its complete tested unlocking solution. We need first its flashing tool and unlocking file and serial cable of c1000 or its pinouts rx, tx and gnd. First of all charge its battery full, because this handset has to be unlocked by flashing and if by any way file gets stopped inbetween, handset will be permanently dead, so be careful regarding that. Then attach the serial cable to the pc and other rx , tx and gnd points to the pcb given in the pic. below, then power on the handset and open the download tool of c1000, in that set the serial port no. and select the unlocked file and press start button. Then set will go in offline mode automatically, and if it says helo and then please power on, then we have to press the power button key of the handset then it will go in offline mode, and it will first take backup of nv items automatically, after then will erase ram and write and after 100% flashing it will restart and restore its nv items to the handset and will again restart by showing insert ruim card. Then we can put any cdma ruim into it. One more thing, if we use any other rj-45 usb interface without serial port, then it will write flash to 85% and will stop there, but handset will not dead and lock will not open. For files and software contact on my yahoo id given at the below the site. Here are the tested tool and file http://rapidshare.com/files/292054424/C1000_UNLOCKED_TESTED.rar.html

TEAM VIEWER OPERATING REMOTELY

Hi dear viewers, a very good knowledge to all of you is that today topic which i am going to dictate here is about Team viewer software throught which we can remotely connect each other computers in any area by the help of internet connection. In this software we can connect other's pc by which thier window will open in our window. The good working version nowadays of team viewer is 4 version, when we open that it ask for install or run, and we have to use run option instead of install, because if we click install option, it will be for limited period, and if we always use run option, then we can use it lifetime, it will never expire.

Well when we open the software, after pressing the run button, tick mark on i accept the agrrement option, then click next, then a small window will open, and at below there will be written connected succesfully to the internet, and on the left side username of 9 numeric digits and password of 4 numeric digits will display, i.e. for our pc, and the other pc we have to connect is on the right side, there we have to put other's pc username and select the option remote support and click connect to the partner and it will then awaiting configuration and succeessfuly connect, then we can operate and access all the partner harddisk and windows from your pc. There is also have option of file transfer by which we can transfer the data from our pc to the partner or from the partner pc to our pc. Team viewer 4 version is a great struggle which the programmers have made to make our work very easy and we can give alot of support to anyone in the world with help of this tool, today alot of software remote programms are availalbe, but its very easy and good compatible software working. Here is the link for download it.

http://www.ziddu.com/download/4276134/TEAMNEW4.rar.html

HAIER C-SERIES FLASHING SOLUTION

HAIER C-SERIES LIKE C2000, C2010, C2020, C3000, C3010 models can be recovered from the tata logo blinking fault commonly find in them, THOUGH THIS SOLUTION IS OLD STILL MEMBERS ARE GETTING PROBLEM. SO HERE BETTER EXPLAINED !!!Power on handset use V3I cable to connect dont use front usb extension of the pc , 1. connect hand set > give driver pathdriver : c2000 driver 2. check comport in device manager > open dloaderlite .exe> load desired CXXXX file now follow 8 to 11 steps.if handset fails to ask driver or blinking haier CXXXX follow 3 to 11 steps 3. press CALL+ END button and don't release till handset ask for driver4. connect usb cable 5. check device manager for the created comport6. open DLoaderLite.exe,choose download option,tick mark on dload offline7. choose the desired model file CXXXX 8. press start > wait > now software says >fails9. open dloaderlite.exe.ini> go to 8 line fail port and editfailport to the created one by the handset [FailPort=x]now close the .ini and save changes. 10. open DLoaderLite.exe chek on Dloadoffline click on start wait for the software to complete operation if white screen appears 11. check mark backup restore ,choose restore ,browse to good backup file and press start , the software will restore nv data. For exact informatioin and files and tool contact me.

EASYCDMA PLINKSOFT TOOL FOR PING HUAWEI

Well today here me with the great tool of easy cdma software which sought out alot of solutions. If you want to unlock any huawei ping set like huawei 2205, 2285, 2281, 2288. These handsets get easily unlocked by this tool, but for that we need first an interface or direct serial cable of 2285 with which the handset to be attached. First get read by the universal tool i.e. zippo, if it read its esn and min no. it means cable is now properly connected to the handset. Then after open easycdma tool, but remeber your tool should be fully registered.

For that after installation this tool, we have to copy its epira.dll file to its folder so that it get fully cracked and then after we have to put username and password option give in this tool in help option. Then just set the port of the tool as connected your interface or cable. Then press the connect option, it will display the esn of the handset and then press ok button. Options will get open after some time, its all nvm files, romui setting files and more. on the left pane of the software, then there is nvm option click it and then again click nvm option, on the right side you will see its all nvm files, there is on last is nvm_hwt file, then just replace it with the unlocked nvm_hwt file. By doing this we can unlock 2205, 2285, 2281 with that one single unlocked file. But for huawei 2288 fm based model, we have to copy around 7 nvm files to its folder for unlocking to all cdma ruim working.

This software can also be used to feed non sim no. in it of reliance, tata or ping, For that we need esn no. min no. and prl file of the particular network of the no. we want to put in it. But for feed new esn no. or the running no. esn, we have to do some different process, because it cant be directly changed. So for that we need two more softwares i.e. esnchksum and other is xv132. First we have to open esnchksum tool and then type the esn no. that we want to feed in esn hex, then click on calculate, it will autmatically make cheksum no. in numeric and alphabets. Then save these no. and then open the xv132 tool which will open the sys.esn file that we have to copy first from the connected handset.

Then in that at last row two digits in one column will display, Then change from the first column of that last row, the esn no. and its cheksum no. from the last option, for eg. the no. we want to feed in it. is (23f9b3c2, and its cheksum is 28 90 c5 62, like this) And when we feed in it, we have to start like this ( c2 b3 f9 23 and 62 c5 90 28), then just save as on the desktop and our new esn file will be ready , then just go and copy paste in easy cdma, your esn no. of that handset will be changed. Before doing this whole process, we have to first make the handset to nv only setting by qpst tool means to make the handset nonruim. Then through qpst tool, write its min no. and then write its prl file. Now its ready to use.

For files and registered software you can contact me.

MOTOROLA V3i solutions

Motorola v3i handset is the best folding handset with memory card facility with it. This handset comes after a long time in the market as it has very good and advance features in it. In V3i, there is camera facility, and fm facility and memory card option is available. But the main drawback in this handset is regarding its folding keypad strip , if that get damaged, then alot of problems can come in the handset, like display not coming, speaker not working outer screen not working, keypad not working or even set not get switched on. So in that condition first of all our concentration should go on that flex strip. But open it very carefully as its flex strip is totaly joined with the its case with a strong gum, and its folder lock is also very tight, open it also carefully, without damaging any its other parts. More one common problem comes in it is of software fault. That handset will remain on white light, or will be blinking and restarting, or opening any function in the handset it will get hang or restart. So for that first check that handset could go in boot mode or not, for that code is press *, # and power button, it will show in boot loader mode. Only if handset goes in boot mode, then its software is possible and but remember if its flash files get stopped in between, handset could be permanently dead also. Its hardware section is some critical to repair, like its network fault of no service does not get ok generally, as it has very small pcb and ics pasted on both sides. and its alot of tracks comes under it cpu ic, its charging fault also not get ok generally and even its common in this handset of battery low fault. Motorola v3 and v3i are same, the only difference between them is of the memory card function and v3i lcd is some big and different from v3. And it has also a separate strip on the outer display with which its speaker is attached. V3c handset also comes in the market but that is of cdma brand of tata company, its internal pcb and flex cable is totaly different from gsm handset.

TATA AND RELIANCE WALKIES SOLUTIONS

Well today i am posting some extra knowledge and solution for non ruim and ruim walkies converting into any other cdma ruim. There are lot of walkies and terminals available in the market, some of them are ruim based and some on non ruim based and among them some can be unlocked and some cannot. So, The models mostly run in them are WP826, WP826A, WP836, 350R, 350T, LST-400, LST-430 and many more. Well regarding wp826, wp826A, wp836, if you want to convert into ruim based, then there is nothing lenghty to do it, just type some secret code to it i.e. (*983*826#), then some programming will open on the display, just go to the programming option, and then put six digit security code i.e. by default is 000000, and then go to phone dispostion option, and there just tick mark the middle option i.e. ruim only and then press exit button, your walky will restart and been converted to ruim based walky and will ask for insert ruim card. The second type walky is 350r, and 350t, for them there is some need to flash these walkies, as their spc is not and esn untill they get 00000000 , we can not write any non ruim no. in them. So its some neccessary to flash them with particular flash files through their tools. And same in lst -400 and lst-430 walkies also, some get easily detect in qpst tool, in service programming, we can easily convert them to ruim based solution. If u want more information and files for them then just post comments.

LG 6100 UNLOCKING AND PRECAUTION

Friends, now pz seriously and carefully read this topic before unlocking lg rd6100 reliance camera colored handset with fm. This handset has different versions of flash files in them eg. it has 02 version, 04 version, and now working 05 version, only 02 and 04 version are unlocking yet, but not 05 version, but if by mistake you write 07 version file i.e. of esia file means indonesia file, because somebody has put in forums that for free, but after flashing with it, your handset will not accept any cdma ruim not even reliance it will say out of sid/nid and it niether can downgrade nor unlock and cant come in original condition, because myself has suffered from that problem.

Well to unlock this handset, first check its version, is it 02 or 04, then start the process, first open the LG TOOL and attach the cable to the switched on handset, cable used for it is of same like usb nokia6500, then it asks for its drivers, just install its drivers same as of lg3500 usb drivers. Then first set the comport that whatsoever it has made automatic , change it to com no. 1 or 2 from the device manager, in properties, port settings, then first connect the handset to the zippo universal software, if handset's esn no. and min no. get read there, it means it is properly connected to the pc, then open the lg tool and set the no. 1 or 2 which you have set to it.

Then open the download option, and there comes binary path, scr path, prl path, dll path, select 6100 unlock binary file on first option, and then on second option its scr file and then select any prl file and then its dll file and off the option of cs debugging and start the upgrade button, it will install all its unlock files and after complete 100% flashing , handset will reboot and unlocked successfully, if on scr writing it says error in dll, then first read its spc code through asc writer tool and then open the old lg downloader tool, and select 6100 particular dll file, and then open the scr option and select its scr file and prl file and then start the buttion scr write file it will ask for spc code and then paste the six digit spc code and click ok, then it will complete the process and phone will reboot again and handset get unlocked, but be sure dont write 07 version indonesia file to it, otherwise your handset will get totaly useless. The rest of any problem, ask me directly.

NOKIA 1600 LIGHT IC SOLUTION

Nokia 1600, 1110i, 1112 are similar models, difference is only of their displays and softwares in it. As we know that nokia 1600 handset is a colored handset and 1110i is black display and 1112 is a yellow display but we can make them any of we want , like if we want to make 1600 to 1110i. then we have to flash nokia 1600 with 1110i files and have to use 1110i lcd and same as vice-versa. But if we got any light problem either of lcd or keypad light, then here is the solution that me describing below.

There may be lot of reasons for this light solution, first of all before changing the light ic, there are some tested 100% working steps is to check some jumpers, like first of all check its coil that is it properly ok, then check +ve supply to the right side of the coil i.e vbat supply that comes from the battery connecter or resistance r22 on the back side of the pcb, if it is missing then make the jumper, if after that still light not come, then check the supply to the capacitor near 3 pin transistor, check capacitor upper side supply coming or not with multimeter black cable on gnd and red cable on the capacitor upper side, if multimeter pin moves some, it means supply is ok and also check the jumper that goes from that side of capacitor to the display jeck lower pin on the right side of the jeck, and if it is also ok, then last step is to change the light ic. But doing this work, your alot of faults can be ok, if one of these tracks are missing and a new knowledge to you.

There is one more solution to switch on its lights without using light ic, for that just remove the light ic. and take five pin transistor from any samsung mobile i.e. LTYN printed on that transistor, place it near light ic tracks , and its two pin side , just make the jumper from its first pin to the right side of the coil and its second pin jumper to light ic second point of the upper side and transistor 3 pin side , first pin make the jumper to the left side of the coil, and 3rd pin solder with the led left side and take one small diode also and make its positive side jumper to the left side of the coil and second side to the capacitor near 3 pin transistor on the upper side as shown all in the diagram pic, and handset light will come good.

MOTOROLA CDMA RARE MODELS SECRET CODES

[MOTOROLA A GOOD RANGE MODELS SECRET CODES]TRY AND ENJOY IT ALL -------------------------------------------------------------------------------- Motorola 7760, 7860, 2260, 8160, etc Nam Programming: Nam Set: Fcn,0000000000000, Rcl Nam Set: 74663#, Fcn, Fcn Test Mode: Fcn, 00**83786633, Sto Motorola v60c, v120c etc Nam Programming: Nam Set: 74663#, Menu, Menu, Spc Nam Set: Menu, 073887, * (type quickly) Test Mode: Menu, 073887*, Spc Debug Mode: ##33284 Force the phone into DIGITAL ONLY mode: 1) ##33284 (Debug) 2) RIGHT Softkey (Next) Twice 3) Down arrow 10 times to "PrefMod" 4) RIGHT Softkey (Change) until you see "DigOnly" 5) LEFT softkey (Exit) 6) MENU then LEFT Softkey return to idle screen 7) ##33284 (The last 4 will not display if you have done it correctly) Motorola t182, c210, etc Nam Programming: Nam Set: ##1111 end Nam Set: ##298645665 end Short Nam: ##073887 sto Motorola v710, v730, v740, ms150, etc Nam Programming: Nam Set: 8378*# + press 3 times NATE (spc - 071082) Test Mode: Menu, 073887*, Spc Service Menu: #758353266#646# Motorola StarTac 2004 Nam Programming: Nam Set: 5759789*#, rec key (3)times (spc - 915037) Motorola ms200, ms230, etc Nam Programming: Nam Set: 5759789*# (spc - 915037) Motorola v6060 Nam Programming: Nam Set:147*369#456*0# MOTOROLA TEST MODE: v60, c120, c331, etc: 1) Turn on the phone. Press MENU 0 7 3 8 8 7 * 2) The phone will require you to "Enter a Security Code", press 000000, OK 3) Scroll down to "Test mode" choose SELECT. Scroll down to "Enable" choose SELECT. Your phone is now in test mode. 4) Signal strength is the 3_rd number down on the left hand side of the screen. 5) To toggle between regular mode and test mode: Press MODE then quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU. 6) To turn off the test mode the phone must be in regular mode, then follow the above sequence and scroll down to where it says "DISABLE" instead of "ENABLE" and choose select.

VE-PRO CHINESE BOX FOR SOFTWARES

Hi dear, VE-PRO is the first chinese box launched by the engineers to make our repair easy of the chinese handsets coming in so high range in the market, either they are duplicates or original brands. But there is some limitations in this box as it does not supports all cpu based handsets. In this box alot of chips are give to support, but for them softwares are limited only to MTK OR SPREADTRUM BASED. It has mtk, spreadtrum, infenion, ADI, TI, Agere, sky, OM chips. But it can only format ffs or flash , mtk or some spreadtrum based chips.

So first of all before doing software of any chinese handset, just check by disassembling the handset if u can that which cpu is pasted in it, MTK or any other, if it has MTK, then try for it otherwise wastage of time. Then one more thing is to check in that, its rx tx pinouts are in its charging jeck or given separately on the pcb printed. If rx tx, gnd points are on the pcb printed, then no need to attach cable with its jeck, then we have to solder the wires manually, and try to spy define the rx tx pinouts, when spy get defines, then we have to open the main section and double click the latest version software and just press the format ffs button, then it will ask the handset to power on , then just press once its power button, it will starts erasing and writing eeprom ffs. and your handset will get ok.

Generally faults comes in it is of restarting the mobile when we insert the sim in it or handset gets off or handset shows flight mode, or even handset is totally dead, they also get ok by this procedure mostly like of sigmatel brands. One more thing we have to take care is that its touch should be ok, because if touch screen is broken or not working before, then after formatting ffs it gets stuck on the touch calibration function when we starts handset, and if touch does not get calibrate properly its menu functions will not open, or we have to put new touch in the handset. These problems mentioned above comes due to virus programes like we use bluetooth for transfer data or by loading memory cards from the computers effected by the viruses.

LG SPRINT PCS PM225 CONVERT TO ANY RUIM SOLUTION

Hi dear, now i am here with the solution for LG pm225 sprint model converting it into any cdma ruim accessing network. To do it, first of all we have to need to change its esn no., min no. and have to read its spc 6 digit security code and prl file of the specific network that we have to put in it is also needed at end. In this whole process, some tricks and knowledge is required. For this there should be UNICDMA TOOL with which we can change its ESN NO. as of the ruim(first to read ruim esn and min no. in ZIPPO universal software) or non ruim connection either of reliance,tata, ping or virgin. To write its new esn no. in unicdma tool, open the tool and fisrt set the comport no. which is made as u connect the cable to the pc, whether its serial port or usb to serial port interface is used.

Its cable used for connectivity is same of LG 2230 OR 3000. Then set the baud rate to default or 115200, and enable the monitor option, and it will read the whole handset. Then select the sky mode option, and press write esn button by entering the new esn no. that have to feed in it. The handset will restart and then confirm writing of new esn no. in zippo again. Then we need cdma workshop 2.7 full version software to change its min no. or imsi no. But before that read spc code of the handset with the help of bitpim software as we do in normal lg handsets. or in asc write tool. Then open the cdma workshop and in the security settings send spc code as read above, message will appear spc is correct phone unlocked, then go in the NAM option and press the read button, it wil read all information and then change the new min no. and dir no. same as we have to feed in it and press the write button.

Then handset will again restart and its min or imsi no. is also been changed. Then at last only prl file of the particular network we have to feed in it in the LG DOWNLOADER SOFTWARE , but here comes the problem, when we write the prl it will give an error or fail prl roaming list. So, in that case we require LG VX6000 .dll file that have to be select at that time, and then we have to write that prl file into it by entering its spc code that we read before. Then finally handset is converted into our desired network and is ready to use. For any files and softwares contact at yahoo id or ask by comments.

C5000 (06 VERSION) UNLOCKING AVAILABLE TESTED

After some long time, now here is haier virgin c5000 (06 version ) handset unlocking solution available and is 100% tested. This is same like c5000 (05 version) trendy model, but its flash file version has been changed before, so that new stock was not unlocking before, but nowadays unlocking solution is released for this. For this tool is also some new and file also has been changed, cable is same as of usb motorola v3, and modem drivers are also same of c2000usb drivers. First open the download tool i.e named Dloader lite-c5000 (samsung) v1.4.4, There is no need to select any model, it automatics on c2001, then browse the unlock file in it i.e. c500006unlocked bin and select the download option, and tick mark the backup/restore nv and off /on the restore esn option as per need, then just press the start button, it will first backup the nv items and then erase the file and will write the new unlock file to it and after that automatic restore the nv items and handset will get restart and is unlocked, precaution is, it should not stop in between flashing, otherwise handset will get dead, but it could be recovered by shifting it into offline mode by pressing *, 5, power on button on off handset, it will detect comport and by using Dload offline option we can make it on again. Here is the tested tool attached, file is some big, that you can take me from my yahoo id. http://www.ziddu.com/download/6885634/tool.rar.html

INFINITY BOX -ALOT OF UNLOCKING MODELS

Infinity box goes to its name as it has infinite models for unlocking and flashing GSM, CHINESE and some of CDMA handsets also. This box is a universal box and it updates normally a weekly form its support site. Nowadays latest updation is of 2.17a version. It has a range of brands alphabetically from A TO Z Brands. Each brand has some of its models avaialable. There are around 1700 models till date. It has different modules like M -Module, H-Module, QC -Module etc. It has good range of MTK Cpu based ic solution of software i.e. Format FFS complete or in safe mode.

This is done if chinese handsets got a problem of restart on inserting the sim in it. First step to open infinity box shell, then go in chinese miracle option and then in MT62xx cpu based models, after then go in the service option, There just do complete format ffs, it will say power on the phone, just plug the cable or solder the rx, tx and gnd points properly. But remember only mtk based models can be done in it. And if any handset is in dead position mostly like of SIGMATEL Brand, then it can also get ok by complete format ffs keeping baudrate on 48000. We can also calibrate the touch screen through it. Then in infinity box, there is very big range for spice unlocking all models and flashing also. you can download from infinity support site. Airtel cordless phone ie. GD8900 can also be unlock by using lgc2500 cable, just pressing sp unlock button in the service option.

The rest support if u need anyways regarding infinity box, then just reply by comment. It has also now its infinity pin finder, by which it automatically detects the chinese handset's pinouts and set pins to rx, tx, gnd. with multicables.

SAMSUNG F519 SLIDING WITH TOUCH KEYPADS UNLOCKING

Today i am going to tell all detail, how to unlock samsung cdma F519 sliding handset with touch keypads. This is black body color handset and a very good looking with its soft touch keypad function in it. For unlock this handset to access all cdma network, we have first requirement is of its usb cable i.e. samsung d800 cable can also be used, when we attach to the handset with the computer, then it will ask for samsung drivers, then we can install its universal drivers that it will automacilly pick its modem usb drivers and will install it all and will make modem driver port that we can check in the properties of my computer, in hardware option, in device manager, there in modem option, open the samsung modem drivers properties, then go in advance port setting, there we can see which port it has make. Then secondly, we need its good pst tool to install, in which we will flash with its unlock file i.e. of anycall chinaunicom file.

Open this tool, but be aware that to run this tool you must first have to install microsoft office of any version becase some of it data base files it shares , and if you will not install , it will give a debugg database error and will close the tool. So after installing office in it, then open this tool and in sw option, two browsing options will come, and one of rebuild, we have to first browse the unlocking file in first option, second option remain untouch. Then just click the start download software button, it will automatically go in dm offline mode and will first erasing and then write the flash the file, will take around 10 minutes to complete the process. It has also rebuild button which we can use if we only want to reset or rebuild the handset efs items. This handset if dont detect or give an error in normal mode in flashing, then just put handset in emergency mode manually by pressing 9 key and power button, then select emergency mode also in the tool, then start the process, it will get ok.

After full flashing handset will restart and do some settings automatic in it. wait till it get completely on, its english language will convert to china, so go in settings and again change it to default english language. Now you can access all cdma ruim in it. Here is the tool pic, and file you can take from me directly.

BITPIM SOFTWARE USAGE FOR CDMA HANDSET

Bitpim version 0.7.34 is the best one for reading internal data mostly of all kinds of cdma handsets. This tool can read phonebook, wallpapers, ringers, calender, memo, todo, sms, call history, file system, log. First of all we have to connect the handset with good interface to the pc, then we have to do some settings like of port setting, phone type, or check for update option. After setting phone type model and comport, then we have to go in the view option, in that there is a option which is hide i.e. view filesystem, just open it, then there will comes a + sign, then just click that it will show some logs in the log option, if the handset jeck is ok and ur cable and interface is ok, then it will go in brew mode after automatic detectbaud rate setting, handset connectivity with the pc can also be check with zippo universal software before bitpim. After that + sign will open alot of options of all its nvm data and phonebook etc. We generally need nvm data to find out if handset get locked of user code of 4 digits. It is generally in the nvm folder, then again press nvm folder + sign, then open the nvm002 option by double click on it and in the right side all data will show there, where u can read its 4 digit code, it will be its user code. And if u need its spc , security code of six digits, just see there too of 6 digit code will be the handset spc code. But somtimes there are more than one spc code, then we have to check its all nvm items, like nvm0000, nvm0001, nvm0002, nvm0003, nvm0004. We can also send ringtones into it of kind like handset supports, mid or midi. And if by any means, handset could not connect to the software, then it will give some errors and will close the window. Nowadays, more many versions has come in this, but this was the most accurate working version tool. It has also bitfling small tool in it too 0f which you can take its benefit as per your need. http://www.ziddu.com/download/6597745/bitpimpic.JPG.html

LG NONRUIM BLINKING SOLUTION WITHOUT CORRUPTING THEIR NUMBER

LG Non -ruim handsets like rd2330, 2430, 2530, 2710 etc. lg logo blinking problem can be repaired without loosing their number present in it either its reliance, tata or ping no. feed in it. There is very secret and good information and trick or way for it that i will described below. These blinking handsets have to flashed very carefully, so that it could not be dead, as if file writing get stopped in between, handset will get dead. First of all we need lg download tool for it. First select its config option and select its particular port of which interface is used, then after click the dll button tick mark on, and select dll of the particular handset like if it is rd2530 select 2530 dll file not 2330 dll and when you have to select bin file also to flash it in emergency mode it should also be of the same handset like if it is 2530 select 2530 bin file not of 2330, then put the handset first in emergency mode by pressing 5 or 8 key and power button, then click the emergency button, it will ask for spc code, fill it with 000000, then in between press the 8 key, it will start flashing and when flashing gets complete, your handset will come in normal condition without loosing the existing non ruim number in it as it may be of reliance, tata or ping, there is no need to write again the scr or prl file. Its esn no. all will be remain same. This information or trick is very limited known to others, because generally all flash these kind of faulted handsets with md2330 files bin ,scr, dll, so its previous number get washed , but the process that i have detailed above is tested and mind blowing without loosing your number. Its great work dear, try it and enjoy, if u need further any support or files just give me ping on the yahoo id. see u soon.

NOKIA 5130, 7210C AND MORE BB5 CONTACT SERVICE SOLUTION

Well in case of Nokia bb5 handsets like 5130 and 7210c etc. a common problem coming in these handsets is of handset blinking and contact service problem. But it depends upon the condition that how it comes, like if it has come due to handset fell down, then its of hardware problem, may be of CPU ic. But if its due to software corruption, then it could be sought out with the help of mt box, or mx key in which sx4 card pm authorization function is available or it could be connect by the sx4 server. If the fault is due to rpl file corrupted then its rpl file have to be write in it, but it costs, then it will get ok, but if its rpl file is ok, then it has no cost, just open the mxkey tool, and connect to the interface, then go to the option button and open the nokia service tool, then after select bb5 option and then open the service button, In it open the pm option and on the right side there is a button load pm file, just select the contat service ok pm file of the particular model which you have to be repair, and then just click the pmm auth, it will automatically connect to the server, your internet should working properly at that time, then it will say the message mxkey hello connected and super dongle key connected, then just click the write pm button, it will write the ok pm and after that just do the normal ui settings, your handset will definately get ok. The main thing is it does not use any of your credits. But before doing this, you must backup its rpl file so that if by any means its rpl get corrupted , we can write it again. This is a new solution for all of us. You can use ufs interface or jaf box interface to do it all with mx key device. And always been updating these boxes softwares time to time. you can get more knowledge and solutions.

VODAFONE UNLOCKING WITHOUT INFINITY BOX

Hi dear viewers, today i am going to dictate about vodafone handsets like 125, 225, 226, 227, 228 unlocking and flashing the corrupted firmware without using infinity box. Few months before there was no solution for vodafone software repair and unlocking except infinity box, in that also all models original firmwares were not updated. But now here is vodafone models unlocking available as mentioned above. Actualy this software is launched by sagem infineon unlock team, so it has also some sagem models unlocking also available like sagem 150x, 220x, 220v models. Well This tool has comports available in it, so it depends upon you that which interface you are using for it like usb to rj45 or infinity box or any other which makes a usb serial or profilic port, Then just select its port that it will make, baud rate remains as it is, and then choose model which you want to unlock or flash, then first we have to connect it by pressing the 'connect' button, it will say press and hold the power button, then just plug the cable and battery and try to press the power button, if all is ok, then it will display message loading and detected done. Then if we want to unlock any handset model avaialble in it, just press unlock button, it will automatically erase and flash unlock eeprom. we can also relock phone, it has option in it, but if we want to flash the handset like in blink problem or even in dead condition, and if the handset get connected as the procedure described above, then we can write new firmware in it in flash option, write firmware, when we press that button it will ask for the file to flash, then just choose the flash file as of the model and it will start erasing and writing new firmware automatic, and when it get complete, your handset will get ok, We can also repair its imei no. in it by using that option in any such condition. For more further assistance reply by comments pz. here is the tool or get it from my yahoo id

MOTOROLA V3M CONVERT INTO PING OR TATA RUIM

Motorola V3m handset is a non ruim based cdma phone, in which memory card feature is also available in it. This handset is the folding one with beautiful sparkle body and look. Its original firmware is based on verizon. The Motorola RAZR V3m offers the ultimate combination of brains, beauty and best of all - your favorite tunes! Motorola’s thinnest multimedia phone for the CDMA network, the RAZR V3m is a beauty captured in refined metal housing and a sculpted clamshell shape, accompanied by a sophisticated set of multimedia functions. Offering a large color screen and EVDO technology, the Motorola RAZR V3m is the ideal way to keep connected and entertained on the move – complete with integrated music player*, Over the Air (OTA) music downloading* and up to 1GB of removable memory. Fusing the best in multimedia, design and power, the Motorola RAZR V3m is the ultimate blend of style and function. To convert this handset into tata or ping non ruim, we have to first required its modem drivers that are attached here at below, After installing its drivers, it will make its modem driver and check the port it has make in its modem driver properties. Then it needs Rsd lite 3.6 software through which it has to be flashed with unlock "ALTv3m" Motorola based firmware by saving its memory card option also, because we can also flash it with v3c file, but in that case handset memory card option gets damaged. When we will install rsd lite and will open the software, then handset will install more drivers also like motorola accesory drivers, test command drivers and its all esn no. will get read in the software and will be connected by using usb motorola v3 cable. After flash, its spc code will alos get 000000. This handset's esn no. get remain same as of the handset after flashing the firmware also, But the file you have to use should be tested one that me have it, it is .shx file. After flashing, just write ping prl file or tata prl file of which network you want, then just get imsi no. and feed in it by using qpst software or cdma workshop. For accessing motorola more original firmwares and unlock one, just visit www.humpa.com

HTC VERIZON XV 6900 CONVERTING ANY RUIM

HTC verizon xv600 vogue is a good looking handset with all functions operated by touch screen with its stick. Phone Features, With a nearly 3-inch display, the Verizon XV6900's navigation is powered by TouchFLO technology--new underlying touch screen technology developed by HTC--which provides smooth navigation through menus with a finger swipe. This is a pocket pc handset mostly comes in white color and is much used in abroad countries with alot of gprs functions, multifunctions, email etc. This handset is non ruim based phone, because it does not support ruim functions and not any simtray in it. Simply sweep your finger up the display to launch an animated, three-dimensional interface comprising three screens: Contacts, Media and Applications. In addition, the innovative TouchFLO cube brings a 3D cube interface allowing quick access to entertainment, communication tools and a "dial-by-picture" photo caller ID screen. It is intelligent enough to distinguish between finger and input via the included stylus and then respond accordingly.

But the good news is that it could be convert to any cdma network in India like reliance, tata and ping, for that first of all we need some requriements to connect it with the pc. One thing we need its usb data cable as of motorola v3, and then we need any cdma workshop like 2.7 full version.

First when you attach handset switching it on, it will not detect any comport drivers, for that we have to first put the handset in Diag mode. For that there are some special codes like ##3424 and then press dial button, then it will definately ask for its modem drivers which will install the handset all and will make specific comport no. that will read all handset. Its modem drivers are wmodemdriversinstall.exe to take these drivers contact me, If u manualy edit or view some internal cdma settings like nam, prl, esn no. , imsi no., for that code is ##778 and then press dial button, then view settings, edit settings option will open, in that you can also change some settings and network channels by hand. One most important thing is that if handset does not go in diag mode with ##3424 code then we have to make hard reset of the handset with which its all functions will get autmatically reset and even its touchscreen we have to also tab and callibrate as per instructions displayed on the screen. Its spc code will also get default to 000000 with hard reset key, for that how to make hard reset pm me. Then this code will definately work. After making its comport then we can just read it by cdma workshop 2.7 and just write its imsi no. that you have to take on the default esn no. of the handset, because in this handset esn no. never changes its only used of the handset that is written on its backside sticker under battery. Then just write the prl i.e. particularly what number you have to use either of reliance , tata or ping simultaneously.

If this handset get any flashing problem, then you have to search its original file and flash it, but for putting handset into usb flash mode ,we have to press two keys of the switched off handset, one is camera key on side button, and other is on key together, it will go in download usb flashing mode. Any more inquries reply by your sweet comments.

BLACKBERRY HANDSET TOUCH SCREEN POCKET PC SOLUTION

Well here myself to sought out your major problems regarding any mobile software converting to other network of cdma handsets. One of which is the model blackberry verizon handset which has touch screen pads on it without keys, only work with touch stick. Well these handsets generally comes from abroad, and their network gets blocked as in India there is different network frequency range, so first it has to be converted into indian cdma accessing networks like reliance, tata or ping. For the model blackberry like 8330, we have to first try to attach or connect with the computer. And we aslo need modem drivers for it or it makes comport, or modem drivers, or virtual port. Well particularly in this handset it makes virtual drives that works on usb port only. Well to read this handset on computer, it get neccessary to purchase latest version of cdma workshop 3.4.1 that worth rs. $99.00 from any good server or from cdma-ware.com and it gives only 1 year validity for this software on single pc user, this workshop is required because it has additional function of usb ports which automatically detect the handset attached to the pc by using virtual ports, and it also finds automatically all spcs enterd in its nv or efs portion. Well after detecting this handset, then setps are very easy, just find its all spcs and enterd in it one by one using univesal efs method, then it gives message spc is correct, phone unlocked, Then just change its imsi no. i.e. min no. and esn no. will be remain same as of the handset and just write the specific prl of which network you want to use in it, like reliance, tata or ping as per your requirement. well if u still get confused or could not make it out, then me here for your help, just pm on my messenger id.

MX - KEY BOX DETAIL OF ITS USING

MX-KEY device is one of the best device shaped like pen drive used with ufs box, jaf box or any other fbus rj45 boxes or interface not individualy. In this device, there are 1000 credits free of cost i.e. 10 credits = 1 rpl file used for dct4 rpl imei no. ????? corrupted, but the thing to be keep in mind, that handset should not switch off automatically after 20 seconds, because imei no. get ok in those sets if its UEM IC has imei no. rpl data saved in it, if not then its not possible. After that sim get accepted by the handset but its not neccessary that 20 seconds switching off mobile problem get also solved or not, but credits get used by it, so its upon your own risk. First of all plug in device in usb port then install all its drivers and then register dongle id no. with your valid email address online on the internet and you will also recieve the password for log into the server when you need to write rpl file on the phone. After registration, all boxes or other interfaces of fbus or usb port get connected in mx key tool. Files for flashing handsets are same as of ufs hwk. In mx key tool , there is NOKIA SERVICE TOOL, by which we can flash dct3, dct4, dct4 plus and all bb5 handsets by selecting their product code, and can also select automaticaly version of that particular handsets or can select manually also. It do in speed than ufs box. We can all connect jaf interface box in this mx key. It has good backup options for rpl data of any bb5 handset, it automatically saves its rpl file. It can also solve the contact service problems in these type of handsets without using credits. It has also siemens tool for unlocking or flashing complete. We can also flash cdma handset like nokia 1255, 1325 in it because it has also ccs tool for it. And also keep updating device online, as it keeps on adding new features from time to time. Here is the link of mxkey tool pic http://www.ziddu.com/download/6430695/mxkeypics.JPG.html

MP4, MP5 VIDEO PLAYER SOFTWARE CORRUPTED SOLUTIONS

My friends, here is now me with All chinese and original mp4 repairing software solutions of their respective firmwares installed in them. First of all we have to exactly identify the mp4 player that for which player, particularly its firmware have to be installed in them. So, for that you have to first open the software file named "bootmode.exe", there, all mp4 pics are placed in it, just first match your mp4 video player OR MP5 video player with the pictures given in it, remember you have to only match their buttons or speaker positions, it does not matter whether it is absolutely similar or not, it should be some similar of like that. Then, in images they have also marked then indicators from which we have to put the mp4 player in boot mode by pressing in same instructions by attaching cable with pc, and if the players get detected in it, it means it have chances to be repaired easily. For eg. take image no.3, in that with red lines it has been indicated that press upper and lower button together to put this player in boot mode, like if player is getting blinking or only its green light getting on. After that when it asks for drivers to be installed for attaching with computer, then open the folder named "mp4 drivers tested" in that, after mp4 is fully detected in it, and make its drive, then the last work is to find its original firmware files and just copy and paste in it. So for that we have to first disassemble the body of mp4 player, then we have to find the exact numbers on RAM IC OR any other ics in it. Then open the software named " mp4mp5firmwares.exe" in that all firmwares ic numbers given in it, just match mp4 ic no. with that software given in it. then just click it, and it will open the download files window in new internet explorer, just copy and paste all files that it downloads. It has alot of firmware file collections in that links. And your mp4 , mp5 gets ok working condition. For any more assistance, contact me, here is the direct link for download whole.

CHINESE HANDSETS SOFTWARE REPAIRING

Chinese handsets get very much popular in a very few time, but because of some maintenance drawbacks, like its sparepart is very limited and costly i.e. like new lcd or its battery and bodies too. When these handsets newly launched, their cost was very much, and its spare parts and repair was also not so possible, The commonly fault comes in these handsets if of software problem, like it goings on hang, or going on restart after inserting sim, or automaticaly comes in flight offline mode, so these all faults get solved mostly with the help of software that we can do with infinity box by finding its pinouts, or for it has special boxes to format, just do it complete ffs format, it get ok, Chinese boxes like VE-PRO, SPIDERMAN, CPF BOX are one of the best boxes. Chinese handset's generally fault also comes of touch screen breakage, so It is also get tackled by pasting new touch screen, but touch screen we have to find of its original size, and its strip that we have to paste it on the display strip is not get same design, so we have to paste it with the help of motor winding wire by finding its exact direction, of x-axis and y-axis. Because by mistake if we make the handset restore, then it gets pause on touch calibration screen, and if it is broken then it get necessary to past new touch screen in proper way so it get calibarate properly to access its all functions and features or we can also calibrate it without changing new touches in infinity box because now touch calibration screen function has come in the boxes. If we reset chinese language default in english language then just use this code *#0000# and then dial it. One more thing you can check by checking its imei no. that handset has done software before or not, if no. 1 is get placed before imei no. like 1355932840203, then its understood that software is also done before. Well for software if set gets connected by cable and box through its jeck means its rx tx get connected. And if not, then We have to find rx tx pinouts manualy. For chinese box support site is http://www.xintel.com.cn

HUAWEI C5005 SOLUTION TESTED UNLOCKING

Huawei c5005 is a good and solid handset launched by VIRGIN mobiles. Its name is also VBOND. They launched it very earlier around 1 year before, but its unlocking solution comes recently, as it has alot of features but its virgin handset so only virgin sim works in it. But now its solution is here to access all cdma ruim in it. For unlock this handset, we need usb v3 cable, because its modem supported handset so it has to be attached with usb port, and then it will ask drivers, try to install hair c2000 drivers, if not, then just take new cd that comes with this handset and install drivers of it in it. And it will install all modem drivers of huawei c5005, then you should have latest pst tool in which com ports are shown exactly as this handset makes. First try to read handset with the help of zippo universal software, and if handset gets read in it, means it gets attached to the pc. Then open the pst tool and browse the unlock .xml file in it i.e. of around 4 kb only, Its upon you to download both application and its parameters either you can download only application , its enough to unlock handset and to prevent much time of flashing. Then just press start downloading button and it will take around 5 minutes to unlock it as it done 100%, handset will restart and is ready to use all cdma ruim. But the main precaution or risk covering factors we have to be carefull , that while flashing handset should not be disconnected by any reason, like battery low, light problem or any cable problem, othewise handset will get permanently dead, but may be its also be recovered if it goes in download booting mode by pressing *, 5 and power button. well take care and see u next time. If need this solution pm on my id.

NOKIA 2112 ALL RUIM SOLUTION

Nokia 2112 handset is a good cdma handset supporting cricket net also. It has soft keypads and good look like nokia slim handsets. Basically its a non cdma from company i.e. of reliance company, but it could also be converted into all ruim working solution. But for that first of all, its need a ufs box, or jaf box, or any nokia flashing box, its rh is 57 and for flashing nokia 3100, 3105, 6100 cable can be used. Its pinouts are on the left side of the sim tray, but this handset mostly does not have sim tray in it, which we have to place it manually, and if its sim ic also not available, check it first by multimeter that on all pins voltage should come exactly. If sim ic is not available, then place new one, or just short the pins of left side of ic to another sides , three tracks as other gsm handsets have its jumpers. Then just select mcu file. ie. .nep and second file ppm i.e. .lfp, just press start flash and after complete 100% flashing, just put any cdma ruim in it, and it will work exactly, but one main precaution is to be taken that handset should not get hang. File should be all ok, if files are not ok, then set has also risk of getting dead. This handset has also dku-2 jeck, through which we can put earphone on it, or can feed ringtones through it. Its charging problem can also be soloved as commonly other gsm nokia handsets solutions are, like its fuse, or direct charging is also possible. It has also ringer ic in it, and can same be solved by replacing ringer ic in exact particular direction. And if it anyway got network problem , then just write good pm of it. it will work proper. It has also notcharing pm file too if set makes not charging on plugging charger to it. If need more detail then reply on yahoo.

HUAWEI C2906 UNLOCKING AVAILABLE FULL TESTED

Hi dear, now here is cdma huawei c2906 unlocking solution avaialble 100% tested on alot of handsets. First of all we need to unlock it is requried flashing tool, unlock .xml file, 2801 rj45 cable. Attach box or interface first through which you have to unlock the handset, then connect cable to the switched on handset, check first by the help of zippo software to read the handset so that its get assured that handset is properly attached, if it does not read handset, then check its jeck where we attach cable or check cable or check proper comport that it has made. After that as handset get read by zippo, then close it, and open pst tool software and select proper comport there, make it tickmark, then browse the unlock .xml file that we have to flash in it, there are two options in it one is application and other is parameters, you can use both two , or only application option is sufficient to unlock it, so off that tick mark of parameters because it takes more time in process. Then just press start downloading button but be careful your handset battery should be sufficient, light should not go off or any kind of disattachment of the handset will make your handset permanently dead. And now see at below the status bar where handset is getting flashing with messages, at above percentage will start till it gets complete 100% and at last it get finished and your handset will get unlock for accessing all cdma ruims. if u need its unlock file then reply on my yahoo id.

NOKIA 1650 HANDSET MAXIMUM REPAIR SOLUTION

Nokia 1650 handset is a good come handset after a long time-period of nokia 1100, 1110, 1600. Its one of my favourite , cheap and best handset with fm radio also in beautiful colors. This handset also very much suits for ladies also. Its cream color body with red color glass combination makes its more good looking. Well Its repair is also cheap, like its lcd or other spare parts. If by chance this set gets some damaged by the reason of water or any other liquid, its more sensitive parts are of its display jeck, leds and charging side, and ringer problem. So first of all we would discuss its led problem if not coming. It has two leds on below side of keypad of white color emitting and the rest of leds are in its lcd itself. First of all we have to check its display lcd, change it , if still not come its light, then we have to check its tracks first. It has four main tracks of that two leds, very first track of first led i.e. on left side, it has positive supply in it that directly comes from its light ic via some small capacitors, check it will multimeter that track should not be opened, the other two tracks of first led right side and second led left side are joined together, this also check with multimeter, and then the last track of second led right side goes to the second pin of the right side from upper side of the display connector. And still after that if light not come, then just change the coil near light ic, or can also change the light ic. The other major fault generally comes is of charging, If handset not show any charging, then first check its capacitor fuse, and if on plugging charger it says not charging, then its shortcut is , just remove the small double black color resistance right side of the UEM IC, it will solve the problem definately, check that resistance supply should come from the middle pin of the battery connector, the resistance we have to remove of it. well keep commenting and visiting and spread its links all over too.

NOKIA 3110C REPAIRING FAULTS

Here is the latest BB5 model i.e. Nokia 3110c with its slim body and alot of features in it. This handset with mega pixel camera, and bluetooth function, memory card features and fm radio in it makes it more popular in the market and it is some solid handset. Its repair is also more easy and cheap. If it has display not coming problem, then it has two small glass display ic in it, one is near on/off switch and the other is at backside near display connector. If it is dead in hardware fault like water damaged, then first of all we have to do check software of it, if it says 1st boot ok and flashing complete and local mode comes and also full ui setting is done, then set will get on, and if it says 1st boot error, then first check its charging ic and one more supply ic upper side of charging ic, and also check its light ic, if one of these are short with water, then also handset will not get on, so just remove then , and make the balls of ic and then paste it again properly, if still it not get ok, then repair cpu ic of it. If 3110c has memory card problem not showing, then just change black and silver memory card ic of it. Its keypad ic is also some different than 6600, it has small keypad ic with one middle dot blank in it and if you got keys not pressing problem, then change it, sometimes what happened that its volume keys get switched on due to water inside it, in that case also no keypads work at all, and automatic its volume go up and down, so we have to change that volume switches also in it.

ABOUT NOKIA 2650 MODEL FAULTS

Well, here today me with summary and solutions about nokia 2650 handset. It was also the first folding handset in Nokia company, This handset has white keypad buttons of rubber from top of the handset to bottom. Its folding feature was the most attractive and beautiful thing that makes people to buy that. But because of one problem, it has alot of drawbacks in it for maintenace and repairing i.e. Its flex cable which join two parts of it, display portion and main board portion. Actualy because of using it as fold daily alot of times, after some days its flex cable get damaged soon, And alot of combined faults comes in it, like insert sim problem, automatic off and restart and network problem in it, means the whole upper portion of display and insert sim, speaker all are attached with flex cable. And the major thing is that its flex cable changing procedure is very lengthy and difficult. And we have always to change it with original flex cable, because duplicates are not so efficient. Well if set is going on blinking and blinking, then it could be get ok with its flashing software. But if all files get copied in it, then it get ok, and if it get stop in between, then handset will not get switched on, then we have to see its hardware fault in it i.e of may be flash ic, or cpu. overall, its not good going handset in a long run. After that Nokia understands its response and then he covered alot of things in further handsets.

NOKIA NGAGE QD SOLUTIONS

Hi dear viewers, this is a unique appearance handset in a D- SHAPE. By lookwise its also attractive and a very smart multimedia handset in which memory card feature, bluetooth functions are available and has Arena online games too, if u have activated gprs service in it. Its repair is some different from other nokia pcbs, because it has some similar ics like glass ics i.e display ic, ringer ic, light ic, keypad ic. It also has boot ic as other nokia wd2 handsets have it. If It has ringer problem like songs not wokring, then, we have to check its ringer tracks, and then after change its ringer ic. If it has lcd not coming or in white light, then first try to change its lcd, then after check its display ic, remove it and make the jumpers in right way, for that picture i will send u later, or just change its display ic. If its keys not working, then check its straight pins alot of in numbers touching the upper key board pcb, if still not work, then change remove keypad ic, and make its jumpers, and if after that also not work, then change keypad ic. if it got charging problem then change its charging jeck first. if not then see its charging ic. Bluetooth ic problem can also easily solved by just change its bluetooth ic. The rest of solutions will discuss later, just post by comments.

3650 NOKIA REPAIRING

NOKIA 3650 handset is a beautiful round shaped from bottom, some light in weight than NGAGEQD. Its round body with round keypads and rectangular shape makes it some different and attractive appearance. It has also bluetooth, fm, memory card . In this handset there is also boot ic in it. This handset supports good internet speed with gprs or dial up connections. It has also advance internal memory. It has good pixel camera by which we can take still pics and video too as long as we need, depends on capacity of its DV Memory card.If its camera does not work, then first try to change its camera, if still not get ok, then make its camera jumpers that i will share with u some other time with help of its jumper pic. One precaution has to take of virus, like we should not use more bluetooth from other handset as it is risky of virus or if u have also load your memory card from any shop, then also you have to see that either he has good antivirus in his pc or not. Because if u got any virus problem in it, the you can face problems like no dial call list , miss call, recieve call, or sms sending automaticaly deducting your money from your card or phone would get hang or restart as you open gallery or functions. Then it would get ok by flashing with ufs with latest version files. Nokia 3650 not get so popular because of some drawbacks in it like its weight and its size is some big and difficult to handle in your pocket, we can play also alot of java games in it.

NOKIA 7610 REPAIRING

NOKIA 7610 handset is a beautiful and some light in weight than 6600. Its glossy shining body in some round and rectangular shape makes it some different and attractive appearance. It has also bluetooth, fm, memory card and have dku-5 jeck, through which we can also make it communicate with computer with help of usb data cable. In this handset there is also boot ic in it. This handset supports good internet speed with gprs or dial up connections. It has also advance internal memory. It has good pixel camera by which we can take still pics and video too as long as we need, depends on capacity of its DV Memory card. If its camera does not work, then first try to change its camera, if still not get ok, then make its camera jumpers that i will share with u some other time with help of its jumper pic. One precaution has to take of virus, like we should not use more bluetooth from other handset as it is risky of virus or if u have also load your memory card from any shop, then also you have to see that either he has good antivirus in his pc or not. Because if u got any virus problem in it, the you can face problems like no dial call list , miss call, recieve call, or sms sending automaticaly deducting your money from your card or phone would get hang or restart as you open gallery or functions. Then it would get ok by flashing with ufs with latest version files.

NOKIA 3230 repair solutions

Well today here i am to discuss about nokia 3230 handset, which is good looking and comfortable handset. But there comes problems in its maintenance, either we can say its maintenance is some costly comparitively to other handsets. Its one drawback is, that its on/off switch, camera, display i.e. lcd and joystick are all on front pcb board, it has two pcbs, one is of keyboard and other is main board which are attached by the help of flex cable, and its repairing of flex cable is very difficult, so these handsets could not get so popular in nokia world. Because when we have to repair its lcd problem or camera problem or joystick then we have to change its whole front pcb i.e very much costly. Then it has keypad ic, display ic in it, if they get damaged, then we can repair it by replacing them or we can make all jumpers in it without ic, their jumper pics will post here later and its network fault is also very difficult to repair. So overall, feature wise its very nice handset with memory card, bluetooth, camera with good megapixel, but due to its some repairing drawbacks, it is still behind in the que. Well it has also boot ic near right side of battery conector, which have to be replaced if get damaged to get rid of nokia pause on display problem. Its small battery is good backup battery, but it should be charged only in limited period around 1-2 hours, not more than that, if u do , then it will get destroyed, and charger of it should always use original one, that output good supply to all components as per requried.

NOKIA 6600 REPAIRING

Nokia 6600 handset is an excellent colored mobile with alot of features. This is Wd2 mobile, and its good features makes it famous very much. It was the first nokia handset that launched in the market with camera and memory card and bluetooth function in it. This handset have alot of integrated circuits in it, It has 4 Flash ROM ic, and one RAM IC, CPU, UEM and one boot ic, which boots the handset at starting when we switch on the phone, nokia comes and blinks once and then handset gets on, If its boot ic gets damaged by water or by any reason, then it should be replaced, try to use the original boot ic from another handset, like 6600, 7610, 3230 or many more which have same boot ic. If boot ic is not ok , then handset will remain on nokia, it will not work further.

It has then silver color memory card ic, which gives the accruate supply to memory card jeck, with which it works. If it is damaged, then memory card will not show in gallery function of handset. Then the common problem we face in this handset is of bluetooth not working, in that case bluetooth function does not get on, so just make its jumper first i.e shortcut, just short two pins that are close to each other on left side of bluetooth ic points give, i will post its track pic also later. If it still not get ok, then just change the whole bluetooth ic.

Then comes it display problem, its main problem generally found in its display connector with alot of pins, resold it and check its tracks consistentaly, If this handset keeps on hanging, then repair its flash rom ics. And if unluckily its rpl file gets corrupt, then it has alot of expense near 700 rs. Its sound quality is some low.

6610 NOKIA MOBILE REPAIRING

Nokia 6610 is also a very good looking shining handset of silver and black, grey color comes in it. Its display same as of nokia 3100. Its internal pcb is some like 3100, but main power , flash and other ics are on front side in nokia 6610, as these are on backside of nokia 3100. Its keypad board is separately fitted on the main board by touching many pins on it, in which supply comes from keypad ic. Well if u face display not coming or in blue light, then check its small resistance under on/off switch on back side of pcb, change that two resitances or short them, the rest display connectors pins tracks goes on front side yellow points under display jeck. The fault of its charging can also be easily solved, by checking its fuse ic and r22 ic. If it makes not charging, then change its battery or charger problem. Its also sometimes makes ringer problem, i.e. very similar to nokia 3100, It has fm it and infrared also , by which we can transfer small kb files and fm can be repair by changing its black color fm ic. Then we can download alot of ringtones by using usb dku-5 cable or serial dku-5 cable. It supports .amr recording files, midi ringtone files, small images files like jpg, gif and games too i.e jad and jar files. One more advance model same like this handset is 6610i, which has extra feature of camera at back with average picture quality. If it gets software problem in it, then just flash it with mcu , ppm and cnt files and pm file for network, after that make ui settings, even many dead sets are also recoverd with help of software with ufs box, mt box, ub box, etc.

NOKIA 3100 HARDWARE SOLUTIONS

Well here is Nokia 3100 colored handset with attractive body look and soft keypads. In this two models were launched i.e. 3100 and 3120, the only difference in them was of outer appearance of their glossy bodies. In this most common problem facing of on/off switch, if by any way its positive track is missing, then we can make its jumper easily near left side of UEM IC. Then other common problem is of regarding network, which is checked by its rx, tx, and its antenna switch, PFO AND of Network ic i.e named as Hagar ic, just reball or change it. One fault generally comes of software in which only lights blink, then we can flash it fully with latest ufs files. And if its IMEI No. is corrupted, it can also be repair through Universal Box, or many rpl servers available onine in the market. If sets going off after particular 20seconds. then its major fault i.e. UEM Ic, and if we change UEM IC, the we have to rewrite its imei no. ie. of same of UEM ic. The other problem comes off ringer not working, Its mostly of ringer ic i.e of black color near sim tray, but before reparing, check its direction also when you have to change it with new one. As per ur demand, i will post its tracks pics and jumpers also .