Well alot of blackbery models like 7XXX, 8XXX AND 9XXX are also unlocking by flashing with mfi files.
This process is also easy if done by the proper way and guidance.
I HAVE ALSO UNLOCKED BLACKBERY MODEL 7100R, 8110, ETC. BY MFI FLASHING. The process starts like this, first of all
we need the particular model's firmware file which we have to unlock country lock, then we need complete setup of 718 mb in zip form, in which there is MML SETUP, which we have to install and it will make directory c:\mml\. Then we have also .netframework install on our system. Then we need one configuration file named "configuration.xml " which we have to replace it with the file made in c:\mml\configuration, this is done if you want to unlock handset without using internet.After that we need blackberry usb and modem drivers latest version i.e. 4.7.
After installing all setups, then the data of 718 mb all mfi zip folders we have to extract it in one folder and have to be replaced it all folders like bin, config etc to the folder made in c;\mml\, because if we do not paste it all there, software will give an error after erasing that load mfi file not find on local hard drive. So remember it to do that in the same way as mentioned, Also install MFI LOADER SETUP, Through which we have to tick mark on erase and auto start
options. and when all drivers will be install on it. it will automatically erase mfi and load its unlocked mfi file, After that on Handset NO. 1 WILL BE SHOWN AFTER PASSING FLASH. THEN WE HAVE TO TYPE THE WORD " S T A R T " TO COME OUT FROM DM MODE. THEN THERE WILL DISPLAY "NO APPLICATION DATA" ERROR, NOW HERE WE NEED HANDSET FIRMWARE APPLICATION FILE AND BLACKBERRY DESKTOP SOFTWARE , TO INSTALL ALL ITS ORIGINAL APPLICATIONS, AND THEN AT LAST AFTER
ALL DONE ON HANDSET NETWORK WILL SHOW OFF, THEN GO IN NETWORK SETTINGS AND SELECT PROPER OPTIONS, AND NOW YOUR HANDSET IS READY TO USE ANY GSM RUIM IN IT. ONE MORE PRECAUTION WE HAVE TO TAKE IS TO DELTE VENDOR.XML FILE i.e. in c:\program files\common files\research in motion\apploader, after mfi flashing and before installing its firmware file. FOR MORE DETAILS CONTACT ON ID. HERE IS SOME DATA BELOW -
http://www.ziddu.com/download/7104977/blackberryhardwareandsoftwarelinks.txt.html
http://www.ziddu.com/download/7105049/FrequentlyAskedQuestionsAboutBlackBerryphones.doc.html http://www.ziddu.com/download/7105056/Configuration.rar.html http://www.ziddu.com/download/7104952/blackberylatest4.7fulldesktopsoftwremanager.txt.html
Well for using huawei ec325 modem, if u want to reliance ruim in it, then its not need to unlock the device, but if u want to use tata ruim in it, then we have to unlock it by first updating its firmware, after that we need its software setup, install it properly and then plug in the device, it will automatically install all modem drivers into the pc, then just open the network connection setting in setting option, click new button and type any profile name and number to dial is #777, username is "internet" and password is also "internet" and then save it and click the connect button, internet will authenticate and will be connected successfully. Well for using net in 1080 data card tata, if we want to use reliance ruim in it, then it needs also to be unlocked with its download tool software and unlock file that i have mention in my site before , search it. Then install tata modem software and you can access good internet in it.
But the best speed and efficiency is going nowadays is of Tata photon that is the latest launched. But where network is week of tata, there got some problems. These modems are best to use on the laptops, notebooks and palmtops because its portable, wireless and easy to use. We can also make calls anywhere by using earphones, either we have prepaid internet connection or post paid connection. Well for more information, comments pz. HERE EC325 DRIVERS
http://www.ziddu.com/download/6932262/EC325_DRIVERS.rar.html
To do that we need haier d1200 vpst tool and then its unlock srp file and its proper serial cable or rj-45 cable, first read it by zippo tool and then open its vpst tool and select srp file in script file option in settings, and select its exact port no. and just click update button, it will write its unlocking srp file and hanset will be unlocked for old tata ruim only.
But for complete unlocking, two files have to be flashed by selecting unlocking cp and boot rom files in flash option, and then just press update, then message will appear on the tool "please reset handset manually", then just unplug cable and battery, and again plugin them. fill will automaticaly write and then same again repeat procedure as it displays above message, then second file will also write and hanset will restart and will be ready to access any cdma ruim in it without any problem. Here is the tool and unlock srp file , but for flash files contact pz, or wait later it will be posted free.
http://www.ziddu.com/download/6886140/unlockd1200srptested.rar.html
But now not to worry at all, here is its complete tested unlocking solution. We need first its flashing tool and unlocking file and serial cable of c1000 or its pinouts rx, tx and gnd. First of all charge its battery full, because this handset has to be unlocked by flashing and if by any way file gets stopped inbetween, handset will be permanently dead, so be careful regarding that. Then attach the serial cable to the pc and other rx , tx and gnd points to the pcb given in the pic. below, then power on the handset and open the download tool of c1000, in that set the serial port no. and select the unlocked file and press start button.
Then set will go in offline mode automatically, and if it says helo and then please power on, then we have to press the power button key of the handset then it will go in offline mode, and it will first take backup of nv items automatically, after then will erase ram and write and after 100% flashing it will restart and restore its nv items to the handset and will again restart by showing insert ruim card. Then we can put any cdma ruim into it. One more thing, if we use any other rj-45 usb interface without serial port, then it will write flash to 85% and will stop there, but handset will not dead and lock will not open. For files and software contact on my yahoo id given at the below the site.
Here are the tested tool and file
http://rapidshare.com/files/292054424/C1000_UNLOCKED_TESTED.rar.html
Well when we open the software, after pressing the run button, tick mark on i accept the agrrement option, then click next, then a small window will open, and at below there will be written connected succesfully to the internet, and on the left side username of 9 numeric digits and password of 4 numeric digits will display, i.e. for our pc, and the other pc we have to connect is on the right side, there we have to put other's pc username and select the option remote support and click connect to the partner and it will then awaiting configuration and succeessfuly connect, then we can operate and access all the partner harddisk and windows from your pc. There is also have option of file transfer by which we can transfer the data from our pc to the partner or from the partner pc to our pc.
Team viewer 4 version is a great struggle which the programmers have made to make our work very easy and we can give alot of support to anyone in the world with help of this tool, today alot of software remote programms are availalbe, but its very easy and good compatible software working. Here is the link for download it.
5. check device manager for the created comport6. open DLoaderLite.exe,choose download option,tick mark on dload offline7. choose the desired model file CXXXX 8. press start > wait > now software says >fails9. open dloaderlite.exe.ini> go to 8 line fail port and editfailport to the created one by the handset [FailPort=x]now close the .ini and save changes. 10. open DLoaderLite.exe chek on Dloadoffline click on start wait for the software to complete operation if white screen appears 11. check mark backup restore ,choose restore ,browse to good backup file and press start , the software will restore nv data. For exact informatioin and files and tool contact me.
More one common problem comes in it is of software fault. That handset will remain on white light, or will be blinking and restarting, or opening any function in the handset it will get hang or restart. So for that first check that handset could go in boot mode or not, for that code is press *, # and power button, it will show in boot loader mode. Only if handset goes in boot mode, then its software is possible and but remember if its flash files get stopped in between, handset could be permanently dead also. Its hardware section is some critical to repair, like its network fault of no service does not get ok generally, as it has very small pcb and ics pasted on both sides. and its alot of tracks comes under it cpu ic, its charging fault also not get ok generally and even its common in this handset of battery low fault.
Motorola v3 and v3i are same, the only difference between them is of the memory card function and v3i lcd is some big and different from v3. And it has also a separate strip on the outer display with which its speaker is attached. V3c handset also comes in the market but that is of cdma brand of tata company, its internal pcb and flex cable is totaly different from gsm handset.
Well regarding wp826, wp826A, wp836, if you want to convert into ruim based, then there is nothing lenghty to do it, just type some secret code to it i.e. (*983*826#), then some programming will open on the display, just go to the programming option, and then put six digit security code i.e. by default is 000000, and then go to phone dispostion option, and there just tick mark the middle option i.e. ruim only and then press exit button, your walky will restart and been converted to ruim based walky and will ask for insert ruim card.
The second type walky is 350r, and 350t, for them there is some need to flash these walkies, as their spc is not and esn untill they get 00000000 , we can not write any non ruim no. in them. So its some neccessary to flash them with particular flash files through their tools. And same in lst -400 and lst-430 walkies also, some get easily detect in qpst tool, in service programming, we can easily convert them to ruim based solution. If u want more information and files for them then just post comments.
